www.upyourride.com

Up Your Ride with this Premium Flat Dash Kit for your 2002-2005 Acura RSX. Exceptional quality available in a number of real and synthetic finishes. In addition to meeting OEM specifications, our experienced engineering staff take pride in developing each kit with design, fit and ease of installation in mind. Applies to existing vehicle dash using Automotive-Grade 3M Adhesive Primerless Acrylic Foam Tape, which provides easy installation and yet an unbelievable transformation of your vehicles interior trim! Install time is approx 1 hour.

• INSTALLATION PRECAUTIONS
• Read the ENTIRE installation instruction sheet before attempting the installation.
• Check to see all parts are present and there is no damage to any part.
• When cleaning, clean only areas that will be covered by dash appliqué as discoloring may occur.
• Use protective covers to avoid damage to the seating surfaces
• Do not use shop rags for cleaning factory dash panels. Use paper towels only.
• Do not spray cleaning solutions directly to factory dash surfaces.
• Repeat cleaning steps (4-5 times) if a dash protectant has been applied to factory dash panels. Test with masking tape for oily residue. If masking tape peels without resistance, repeat cleaning procedure.
• Air temperature and factory dash surfaces must be 75º Fahrenheit or more. (Warm to the touch)
• Do not touch adhesive backing prior to installation.
• INSTALLATION STEPS
• STEP 1. DRY FIT AND INSPECT ALL PARTS
• Carefully check placement and alignment of each part to corresponding area of factory dash before beginning installation.
• STEP 2. DASH CLEANING AND PREPARATION
• Clean dash surfaces by applying 3M Prep-Sol 70 (Not Included in Most Kits however Rubbing Alcohol can be substituted) cleaner to a clean paper towel and thoroughly clean each vehicle surface where the wood trim is to be applied. Wipe off the Prep-Sol with a fresh clean paper towel before it completely dries. Fold towels between each part cleaning and apply additional Prep-Sol cleaner as required.
• Clean dash surfaces a second time using a paper towel and Alcohol. Fold the paper towel several times during the cleaning process to provide a fresh surface. Allow alcohol to dry completely. Do not let the alcohol come into contact with any clear plastic surfaces covering gauges, clocks, radios or warning lights.
• To test surfaces to ensure proper cleaning apply a small piece of masking tape to different area’s that have been cleaned. (Use a new piece of masking tape for each area tested.) If the masking tape peels off without resistance, repeat cleaning procedure. Repeat all cleaning steps until masking tape sticks aggressively.
• Apply Adhesive Promoter to all areas being covered with dash appliqué.
• o (Step not required if using 3M promoter-less tape.)
• STEP 3. TEMPERATURE
• Vehicle surface temperatures must be at least 70 degrees F during the installation of the interior trim. The interior trim part should be heated to the point where it is very flexible. Use a hair blower to heat the vehicle interior and trim parts as required.
• STEP 4. REMOVAL OF PROTECTIVE BACKING
• Remove the protective backing from one part at a time. Carefully pull downwards so adhesive does not pull away from part. Lightly heat exposed adhesive to improve bond.
• STEP 5. INSTALLATION
• Place dash appliqué on appropriate factory part and lightly tack into place once properly aligned. On larger parts, install from side to side or top to bottom. Do not adhere from center of part and try to work outwards. Check all movable parts (buttons, switches, vents) to make sure they function properly.
• WARNING: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS MAY VOID WARRANTY.
  
  
  CLICK HERE FOR INSTALLATION TRAINING VIDEO!
  

Sherwood Innovations Inc. was incorporated on February 1st, 1997. Prior to this date, we operated as a Division of Centro Manufacturing for 3 years. Sherwood Innovations has benefited from its association with Centro by drawing on their extensive engineering and manufacturing capabilities as a tier 2 supplier to Original Equipment Manufacturers worldwide. The result is a superior quality product at an exceptional price. Production of this high quality, high value wood dash has resulted in substantial growth in each year of operation. In October of 1999, Sherwood Innovations Inc. purchased the assets of TrimMaster Inc., a major competitor in the dash industry with a strong presence in the OE market. The new company is known as Sherwood Innovations Inc. The company operates out of Toronto, Ontario. Our product line now includes real wood dashes, graphic dashes and molded dashes. In a few short years we've grown from 3 employees to a dedicated and diverse team. In July of 2002, we completed our certification for ISO9001 and QS9000 quality systems. In 2006 we completed our certification for TS16949, the hightest quality standard in the industry. Sherwood Innovations has come a long way in a short period of time but it is our sincere belief that we are only at the beginning of a long, prosperous journey.